|
The picture above depicts a 8' double sided
gondola configured with two sections and one
end that includes: all the trim pieces such as
front kick plates, base shoe covers, and upright
covers.
The double sided sections are designed to be
placed in the center portion of the
merchandising floor and can be used to separate
the store and aisles.
We have double sided sections available in
depths as small as 12" and as deep as 30" with
heights that start at 36" up to 96". Floor
anchors are suggested and available for all
heights above 48". Check with your
contractor, city and county building codes.
Sold
Separately
Upper Shelves available in two inch increments starting at 8 inches to 30 inches
deep. Widths of a standard 36 inch and a 48 inch stocked in the beige black and dove gray colors. 24 inch and the 30 inch available by special order.
Available in all standard finishes, optional finishes, and custom paterns also.
Smaller shelves sit at a 15 degree up slope, flat and a 15 degree down slope. Besides the flat position the downslope position is best for snacks, chips, and candy with a 3 inch high front fence or a one inch high front retainer. The deeper shelves sit at a 15 degree and 30 degree up slope, flat and a 15 degree and 30 degree downslope
The
Convenience
Store End Cap is
configured with
the same
components as
the double sided
and single sided
gondolas.
As it is a
single sided
section in a
double back
configuration it
can easily be
installed right
up against and
existing aisle
of double sided
Convenience
Store Gondolas.
Identify all the pieces used to configure a
section of Convenience Store Shelving.
From top to bottom: top spanner, backs,
center spanner, basic uptight, lower spanner,
base shelf, base shoes, base shoe cover, front
kictplate.
Not show is the splicer spanner used on
sections 78" or higher.
As pictured above you can configure a
complete counter system from front to back using
Gondola Shelving that can be interchangeable
with all of the Gondola Shelving through out the
whole store.
We have available Cooler Shelves. What
we need to know in order to provide you an
accurate quote is basically the size of the door
and the depth of the shelves that are needed.
|
The picture above depicts a 8' single sided
section of Wall Convenience Store Shelving configured with two sections and one
end that includes: all the trim pieces such as
front kick plates, base shoe covers, and upright
covers.
The single sided sections are designed to sit
flush against a wall as the wall will provide
support and stability.
We have single sided sections available in
depths as small as 12" and as deep as 30" with
heights that start at 36" up to 96" and above
with what is known as extension uprights.
Wall anchors are suggested and available for all
heights. Check with your contractor, city
and county building codes.
Heavy gauge steel
wire construction, powder coated for long life
and extra wear constructed for Potato Chips in a
Grocery Store, Candy, Bed Linen, and more.
Freestanding Wire
Binning System Front Fences and Dividers for
Store Shelving allows the
flexibility in merchandising of smaller and lighter products.
The fences and dividers for store shelving have welded on “feet” for attachment
to shelf perforations on upper shelves. Fronts and
Store Shelving Dividers may
be used independent of one another to divides a
shelf into sections of bins.
Vertical wire are
on 1" centers. Chrome plated finish.
|
Standard Coatings
|
Oyster |
Sahara Beige |
Satin Black |
Non Returnable Coatings
|
Blue Gray |
Chocolate |
Dove Gray |
Dover White |
|
Fashion Gray |
True Gray |
Skyline Gray |
Snow White |
Optional Non Returnable Coatings
|
Bright Orange |
Burgundy |
Hollyberry |
Hunter Green |
|
Mandarian |
Neon Blue |
Yellow |
Spectrum Blue |
|
Spectrum Green |
Spectrum Red |
Valencia |
|
|
Freestanding Wire
Binning System Front Fences and Dividers for
Store Shelving allows the
flexibility in merchandising of smaller and lighter products.
The fences and dividers for store shelving have welded on “feet” for attachment
to shelf perforations on upper shelves. Fronts and
Store Shelving Dividers may
be used independent of one another to divides a
shelf into sections of bins.
Vertical wire are
on 1" centers. Chrome plated finish.
The 4 Way Display an island display suited
for a small Convenience Store with Limited Space
that will provide merchandising on all 4 sided
for maximum exposure.
Heavy gauge steel
wire construction, powder coated for long life
and extra wear constructed for Potato Chips in a
Grocery Store, Candy, Bed Linen, and more.
|
